A fiber reinforced concrete manhole cover is a precast cover with fiber mixed into its concrete, in addition to the steel its design already needs. The fiber earns its place in the plant and on the truck, not under traffic. It helps the cover get through stripping, stacking, transport and setting with fewer cracked rims and broken corners. However, it does not give the cover its load class. That still comes from the cover's own design and its load test.
Where precast manhole covers get damaged
A cover can be ruined before it ever sees a wheel, because the weak moments come early. First, the cover leaves its mould while the concrete is young and at its lowest strength. Then the crew lifts it, stacks it and loads it. Each of those steps puts loads on the cover that its design did not check, often through a thin rim.
The edge is the usual victim. A cover is a flat disc or square with a thin perimeter, and that perimeter is where a hook, a bar or a careless drop lands. A chipped rim no longer sits flat in its frame. As a result, the cover can rock under traffic, and a rocking cover wears out its seat.
The National Precast Concrete Association (NPCA) describes this pattern in its fibers white paper: a product that keeps showing cracks or spalls as it comes out of the mould. It names that as a production problem that fiber can solve. Our page on precast and facade concrete follows the same handling chain for larger units.
What fiber does in a fiber reinforced concrete manhole cover
Fiber works because it sits everywhere in the section, including the rim where bars cannot reach. When a crack starts, fibers bridge it and keep it tight. The NPCA white paper also says the same crack bridging makes concrete harder to break apart, so impact resistance improves. In plain terms, the fibers help hold a struck corner together instead of letting it fall away.
The two fiber families do different jobs here:
Micro fiber works while the concrete is still soft. NPCA's utility structure manual says synthetic microfibers reduce plastic shrinkage cracks, improve impact resistance and help reduce chipping when products are stripped.
Macro fiber adds capacity after cracking. If a cover cracks during handling, macro fiber holds the two sides together. The same manual says macro synthetic fiber design should rest on ASTM C1609 beam tests.

What fiber does not do: set the load class
The load class is the cover's job, not the fiber's. In Europe, EN 124 sorts covers into classes from A 15 to F 900 by where they go. Its part for concrete covers, EN 124-4, applies to precast covers made of steel reinforced concrete. So in a cover built to that standard, fiber is an addition to the designed steel, not a substitute for it.
| EN 124 class | Where it goes |
| A 15 | Areas used only by pedestrians and cyclists |
| B 125 | Footways, pedestrian areas and car parks |
| C 250 | Kerbside channels, up to 0.5 m into the road |
| D 400 | Roads, hard shoulders and parking for all road vehicles |
| E 600 | Areas with high wheel loads, such as docks |
| F 900 | Very high wheel loads, such as aircraft pavements |
Fiber does not raise compressive strength either. NPCA's white paper says compressive strength should not be affected. Because of that, a fiber data sheet can never stand in for the class test of a finished fiber reinforced concrete manhole cover. Ask the cover maker for that test. NPCA's manual also says the specifying engineer or the regulator must approve the fibers before the concrete goes in.
Choosing the fiber grade and dose for covers
For precast covers we start from PG PC-40, a 40 mm grade in our range of macro synthetic fibers for concrete. Its band for precast and facade work is 2 to 5 kg per cubic metre of concrete. Sometimes the problem is different. For example, the top face may craze from plastic shrinkage before stripping. Then PG MS-12 micro monofilament at 0.6 to 1.2 kg/m³ targets that. It belongs to our line of polypropylene concrete fibers. If you have both problems, both grades can go into one mix, each at its own dose.
Where in the band should you sit? That depends on the cover's thickness, the mix and how rough the handling is. NPCA's advice is practical. If the goal is less handling damage, run trials in production and find the product and dose that work best. Our technical team designs a starting dose from the section and loading at no charge. We also send a free sample for the trial batches. Our trial mix plan lists what to record.
Do not go above the band "to be safe". More fiber than the cover needs makes the mix stiffer and the top face harder to close. It also costs more, and it adds nothing to the load class. The right dose for a fiber reinforced concrete manhole cover is the lowest one that stops the damage you counted.
What changes in the precast plant
Not much, once the mix is right. NPCA notes that transporting, placing, vibrating and curing all stay the same. The difference is in mixing. Fibers usually go in with the aggregates, and mixing may take a little longer. Our 3 kg and 5 kg bags dissolve in the mixer, so the crew can drop whole bags in.
Fiber needs a little more paste to coat it, so the mix may look stiffer. Fix that with the mix design or a water reducer, never with extra water. Extra water weakens the top face, and that face is the one that takes the wheels.
The top face also needs patience. If the crew trowels too early, fibers can lift to the surface. Our guide to fibers sticking out of concrete covers the finishing sequence. Finally, keep testing for stripping strength. NPCA asks for that strength to be proven by cylinder tests, and fiber does not change the rule.

How to tell whether the fiber worked
Count. Record how many covers come out of each run with cracked rims or broken corners, first without fiber and then with it. Do the same in the yard and at delivery. Our article on fiber reinforced precast concrete explains how to track rejections so the comparison is fair.
Next, check the fiber itself. Every Polyguard grade is 100% virgin polypropylene, and every production batch ships with its own QC certificate. If your specification names a test method, we can issue the test report for it. A concrete fiber supplier should hand over all of this without being asked twice.
Keep the order of things clear. A fiber reinforced concrete manhole cover is still judged by its class test and its design. The fiber's job is to get more covers to that test, and to the street, in one piece.
Frequently Asked Questions
Does fiber give a concrete manhole cover a higher load class?
No. The load class, from A 15 to F 900 under EN 124, comes from the cover's design and its own class test. Fiber reduces cracked rims and broken corners during stripping, stacking and transport, and it barely changes compressive strength.
Which fiber grade suits precast manhole covers?
Polyguard starts from PG PC-40, a 40 mm macro grade dosed at 2 to 5 kg per cubic metre for precast work. Where the top face crazes from plastic shrinkage, PG MS-12 micro fiber at 0.6 to 1.2 kg/m³ can be added, each grade at its own dose.
Can fiber replace the steel in a concrete manhole cover?
Not in a cover built to EN 124-4, which applies to precast covers made of steel reinforced concrete. There, fiber is an addition to the designed steel, and NPCA says the specifying engineer or regulator must approve the fibers first.
Does adding fiber change how covers are produced?
Very little. Placing, vibrating and curing stay the same. Fibers usually go in with the aggregates, mixing may take a little longer, and any stiffness is fixed with the mix design or a water reducer, never with extra water.