Products Polypropylene concrete fiber Macro synthetic fiber Buy concrete fiber Applications Calculators About us Technical notes Contact Request a quote

Technical note

Structural Synthetic Fibers: What Earns a Fiber That Name

Aerial black-and-white view of workers on a large concrete slab under construction, where structural synthetic fibers are specified by design

Structural synthetic fibers are macro synthetic fibers whose effect on cracked concrete has been measured in a standard test and then used in a design calculation. So "structural" describes the job a fiber does in a design, not a word printed on the bag. A fiber earns the name when a designer counts its residual strength toward the capacity of a slab, a lining or a precast unit. Even then, it does not replace rebar in beams, columns or suspended slabs. Here is what has to be true before the word applies, and why micro fiber never qualifies.

What "structural" means in the standards

The clearest definition comes from Europe. EN 14889-2 covers polymer fibers for structural or non-structural use. It calls a use structural when the fibers are designed to contribute to the load-bearing capacity of a concrete element. The key word is designed. A fiber that only limits early surface cracks is useful, but it is not structural by this test.

The same standard also sorts polymer fibers into classes. Classes Ia and Ib are micro fibers, while Class II covers macro fibers. Only Class II is in the running for structural use. In the United States, ASTM C1116 sorts fiber concrete by fiber material, and synthetic fiber concrete is Type III. That type tells you what the fiber is made of, but not whether it can carry load.

Iran's Code 120-4 draws the line by fiber size. Macro polyolefin fibers are at least 581 denier, and micro fibers are at most 580. For macro fibers the code also asks for a tensile strength above 345 MPa. These are entry tickets. They show that a fiber is the right kind, yet they do not prove that it performs in your concrete.

Why structural synthetic fibers are always macro fibers

The short answer is geometry. ACI describes synthetic microfibers as fine fibers, about 0.01 to 0.3 mm across, used mainly against plastic shrinkage cracks. It adds that they do little for hardened concrete. Macrofibers, in contrast, are 0.3 mm or thicker and roughly 12 to 65 mm long. Some have an embossed surface that grips the cement paste better.

That size matters once a crack opens. A long, stiff fiber stays anchored on both sides of the crack. As the crack widens, the fiber stretches and keeps passing load across it. A fine micro fiber cannot do this to any useful degree after the concrete has hardened. As a result, a cracked section with only micro fiber behaves much like plain concrete.

This is why our macro synthetic fibers for concrete are the only grades we discuss for designed use. Our micro grade, PG MS-12, is a fine monofilament. It does an important job, but that job is not structural.

Residual strength: the number behind the word

Plain concrete cracks and then loses its tensile capacity almost at once. Fiber concrete, however, keeps some capacity after the crack. That leftover capacity is the residual strength, and it is the only part a designer can count.

Old industrial hall with steel columns standing on a wide concrete floor

In North America the usual test is ASTM C1609. A closed-loop testing machine loads a small beam at its third points. The test first records the first-peak strength, which describes the beam up to cracking. Then it records residual strengths at set deflections after the crack. The standard gives two preferred beam sizes and notes that results depend on specimen size. For that reason, compare two reports only when they used the same beam.

European practice uses a notched beam test, EN 14651. Shotcrete is often tested in a different way, on a round panel to ASTM C1550. Code 120-4 lists C1609, C1399 and C1550 as the flexural tests for polyolefin fiber concrete. Whatever the method, one rule holds. Residual strength belongs to a concrete mix at a stated dose. It is never a property of the fiber alone.

How a designer uses structural synthetic fibers

Once a lab has measured residual strength, the number can enter a calculation. ACI's Guide to Design with Fiber-Reinforced Concrete (ACI PRC-544.4-18) shows how. It uses standard test results to design for flexure, shear and crack-width control. Its scope includes slabs on ground, pile-supported slabs, composite slabs on metal deck, precast units and shotcrete. It also covers hybrid sections, where bars and fibers work together.

In practice the designer works back from the element. First, the loads, thickness and joint layout set the residual strength the element needs. Next, a trial with the project's own concrete shows which dose reaches it. Finally, the specification names that performance, the test method and the dose. A drawing that only says "add structural fiber" skips the first two steps.

What structural synthetic fibers do not do

The word "structural" tempts people to stretch it. Fiber replaces crack-control mesh and temperature steel only where the design permits. It does not replace rebar, or any reinforcement designed for bending in beams, columns and suspended slabs. If a section needs bars, the bars stay, and the fiber comes on top of them.

Fiber also leaves compressive strength close to where it was. Code 120-4 notes no noticeable change at low to moderate doses. Likewise, fiber does not remove the need for joints and curing. A slab still shrinks, so it still needs the joints its designer drew. Our note on reinforcing concrete with fibers covers where the economics work and where they do not.

Why micro fiber is never structural, but still worth using

Micro fiber fails the definition by design, not by quality. Fine polypropylene concrete fibers work in the first hours, while the concrete is still plastic. They limit plastic shrinkage cracks. They are also one of the recognised methods to reduce the risk of explosive spalling in a fire. Neither job involves carrying load across an open crack.

Some mixes need both effects. In that case micro and macro fibers go in together, each at its own dose. One never stands in for the other. If a seller offers a micro fiber as structural, the product does not match the job.

Checking structural synthetic fibers before you buy

Ask for evidence, not adjectives. Four items cover most of it:

  • Proof of a macro fiber, Class II under EN 14889-2 or macro under Code 120-4, with its length, size and tensile strength on the data sheet.

  • Residual strength results for the test your specification names, at a stated dose, with the reference mix described.

  • Quality control certificate for the production batch you receive.

  • Trial batch in your own mix, tested the same way, before the full order.

The macro grades below show the dose bands we work within. However, the final dose comes from the design and the trial, not from this table.

Typical useGradeLengthDose (kg/m³)
Crack control, not full reinforcement replacementPG EC-4545 mm2–4
Precast and facade unitsPG PC-4040 mm2–5
Industrial floors, slabs on groundPG MF-5454 mm3–7
Shotcrete and tunnels, tested to ASTM C1550PG SC-4848 mm4–9
Dark concrete-lined tunnel opening towards a bright exit

Every Polyguard grade is 100% virgin polypropylene, made on automatic extrusion lines under an ISO 9001 quality system. Each batch has its own QC certificate, and on request we issue test reports for the method your specification names. As a concrete fiber supplier, we also design the dose free from your section, loading and exposure, then send a free sample for trial batching. Before the trial, our trial mix test plan shows what to measure, and our standards page sets out which fiber class may count in a design.

Frequently Asked Questions

What makes a synthetic fiber structural?

A fiber is structural when it is designed to contribute to the load-bearing capacity of a concrete element. In practice that means a macro fiber whose residual strength has been measured in a standard test at a stated dose and then used in the design.

Can micro fiber be used as a structural fiber?

No. Micro fibers are too fine to carry useful load across an open crack in hardened concrete. They limit plastic shrinkage cracks and are one of the recognised methods to reduce explosive spalling risk, but they are not structural.

Do structural synthetic fibers replace rebar?

No. They can replace crack-control mesh and temperature steel where the design permits, but not rebar or other reinforcement designed for bending in beams, columns and suspended slabs.

Which test shows whether a fiber concrete has residual strength?

In North America it is usually ASTM C1609, a beam test that reports first-peak and residual strengths. Europe uses the notched beam test EN 14651, and shotcrete is often tested on a round panel to ASTM C1550.

Keep reading

Related notes